Solutions: Insulators


Tgard K52



Thermally Conductive Insulator

High Thermal and Dielectric Performance Insulator Pad Tgard K52 is a high thermal and dielectric performance insulator pad consisting of a ceramic filled phase change compound coated on MT Kapton film. Tgard K52 phase change coating all but eliminates contact thermal resistance. The phase change coating melts at 52ºC and replaces all contact areas that contain air. TgardTM K52-1 is ideal for applications requiring the best thermal performing insulator material.

Show More

Tgard TNC-4



Thermally Conductive Insulator

Low Cost, Medium Performance Insulator Material In Automotive Electronics Applications Tgard TNC-4 is an electrically insulating, thermally conductive, heat curable adhesive insulator. It consists of a thin electrically insulating PI film coated on both sides with a thermally conductive polymer composite material. It can be used to permanently attach IC or other electronic packages to heatsink.

Show More

Tgard 20



Thermally Conductive Insulator

Low Cost, Medium Performance Insulator Material The Tgard 20 is designed to solve over heating issues such as lower component efficiency, premature component failures, size limitations and other performance problems for today’s computer power supplies. The Tgard 20 is a film-based product designed to resist cut through in sc rew mounting applications while providing a more consistent breakdown voltage over other insulator constructions. The phase change coating on the film core provides an excellent mating surface for low pressure clip mounting applications.

Show More

Tgard 300



Thermally Conductive Insulator

Tgard 300 is a medium thermal performance insulator pad consisting of a ceramic high temperature silcone rubber coated on electrical fiberglass. Tgard 300 is specifically designed for applications that require low component mounting forces. The unique formulation will enhance thermal performance which minimizes thermal resistance at low mounting forces. The uniqe coating formulation offers an excellent mating surface for low pressure clip mounting applications.

Show More

Tgard 5000NT1



Thermally Conductive Insulator

Tgard 5000NT1 is an excellent dielectric material with good thermal performance consisting of polyimide film coated with ceramic-filled, high-temperature silicone rubber. The unique natural tack on one side is specially designed for ease of placement on the component. The inherent tack also enables repositionable after the initial placement and assembly error minimization.

Show More

Tgard 200



Thermally Conductive Insulator

The Tgard 200 is a high performance interface pad. Consisting of a silicone/boron nitride composite, these fiberglass-reinforced pads are used when the lowest thermal resistance and highest dielectric strength are required A high-tear, cut-through and puncture-resistant product, the Tgard™ 200 is tough and strong. Burrs cause no problems for the material and the pad will not dry out, crack or fail when pressured between mating parts. The Tgard™ 200 is available in the following sizes: 0.010""; (0.25 mm) die cut shapes only 0.020""; (0.51 mm) sheets and die cut shapes 0.030""; (0.75 mm) sheets and die cut shapes

Show More

Tgard 5000



Thermally Conductive Insulator

Thermally conductive electrically insulative material Tgard 5000 is an excellent dielectric material with good thermal performance consisting of a polyimide film coated with a ceramic-filled, high-temperature silicone rubber. Tgard 5000 is ideal for applications that require a delta temperature across the interface of 2.0ºC/watt or higher on a TO-220 clip mounted @ 50 psi pressure. Tgard 5000 has high dielectric strength for the AC side of a switching mode power supply. Tgard 5000 is tough resulting in an exceptional cut-through resistant material.

Show More

Tgard 500



Thermally Conductive Insulator

Thicker Thermal Insulator Pad Prevents Electrical Shorts In Automotive Electronics Applications Tgard 500 is a medium thermal performance insulator pad consisting of a ceramic filled high temperature silcone rubber coated on electrical grade fiberglass. Tgard 500 is designed for applications that require traditional thickenss to prevent electrical shorts from stamped aluminum heatskinks used in switching mode power supplies (SMPS) and debris from aluminum castings used in automotive motor controls.

Show More